China Pipette Tip Manufacturer
  • Home
  • Products
    • Universal Pipette Tips112
    • Automatic Pipette Tips7
    • PCR
      • PCR Plates12
      • Single PCR Tubes9
      • 8-strip PCR Tubes17
    • Centrifuge Tubes27
    • Deep Well Plates23
    • Magnetic Rod Sleeves1
    • Safety Goggles1
    • Robotic Tips
  • News
  • About Us
    • Company Profile
    • Certificates3
    • Factory Tour12
    • Cooperative Partners15
    • Company Culture
  • Contact Us
Get a quote
Home/News/The Inspection of the Pipette

The Inspection of the Pipette

Aug 13, 2022
In general, pipettes require regular inspection. Regular inspection is mainly to ensure the better accuracy of the pipette and the inspection results. The pipette is a measure-out type, which is greatly affected by the environment and operation. Therefore, when adjusting the range of the pipette, the counterclockwise rotation is used in order to ensure the accuracy of the measurement during the rotation of the knob. Use your index finger and thumb to adjust the knob. If the maximum range is exceeded, adjustment of the knob is also required. In addition, special attention should be paid to the adjustment accuracy taking into account the damage to the pipette caused by the internal mechanical jamming. Therefore, when assembling the liquid gun, pay attention to the assembly process of the pipette tip to avoid loosening of internal parts. When installing the pipette tip, pay attention to the installation method of the pipette tip. It needs to be inserted vertically and rotated slightly left and right at the same time to help the knob match with the pipette tip. In addition, two aspects should be considered for the unqualified sealing. The first is the pipette tip. Consider checking the installation of the tip. Pay attention to whether the tip matches with the instrument or there is an installation error, or if there is a problem in the system itself. Replacing the tip can help achieve the purpose of the smooth progress of the inspection. The second is to check that the gap between the internal sealing ring of the pipette and the piston is too big, which may be related to the aging of the sealing ring. The leakage caused by this problem can be solved by applying a small amount of Vaseline evenly on the piston, or using the same sealing ring to help solve the problem of sealing. If there is still a leakage after applying Vaseline on the piston, it is necessary to replace the sealing ring of the same type.
 
In addition, when solving the problem of volume error, the volume of the pipette can be adjusted; the occurrence of volume error can be identified, and the volume can be increased or decreased by the Allen wrench equipped with the pipette itself. First, the current capacity value needs to be verified, and the pipette needs to be adjusted to the minimum verification point. The difference between the current capacity value and the marked capacity value needs to be calculated, and the adjustment hole can be adjusted with a wrench. Detection should be performed after adjustment. Through calculation and multiple measurements, observe whether it conforms to the verification regulations. If the corresponding requirements are met, continue to inspect. The pipette can be adjusted to the middle inspection point. If the middle inspection point meets the verification requirements, the maximum verification point can be detected, and the detection and adjustment can be carried out several times to determine whether the different verification points are correct. In accordance with the requirements of the regulations, multiple corrections and tests can be carried out until the values ​​of the three verification points meet the corresponding verification regulations.
 
Conclusion
A pipette is a highly accurate measuring instrument. Its accuracy will directly affect the experimental results. Therefore, it is necessary to carry out corresponding verification of the pipette, and to correct the technical problems in time to ensure that the measured data is more accurate and reliable. At the same time, it is also necessary to pay attention to the use of the instrument and operate strictly to prolong the service life of the pipette.


Previous: Research on Common Technical Problems and Solutions in Pipettes
Next: Chemical Anti-fogging of Goggles for Coronavirus

Name*
E-mail*
Rate*
Comments*

About the author
Teresa
Teresa
pu*****************om
Teresa is a skilled author specializing in industrial technical articles with over eight years of experience. She has a deep understanding of manufacturing processes, material science, and technological advancements. Her work includes detailed analyses, process optimization techniques, and quality control methods that aim to enhance production efficiency and product quality across various industries. Teresa's articles are well-researched, clear, and informative, making complex industrial concepts accessible to professionals and stakeholders.

Latest News

Different Types of Laboratory Tubes and Their Uses

Different Types of Laboratory Tubes and Their Uses

September 3, 2024
News Detail
Purpose and Precautions of Magnetic Rod Sleeve

Purpose and Precautions of Magnetic Rod Sleeve

August 27, 2024
News Detail
Considerations for Precision Automated Pipetting

Considerations for Precision Automated Pipetting

August 21, 2024
News Detail
China Pipette Tip Manufacturer
Products
  • Universal Pipette Tips (112)
  • Automatic Pipette Tips (7)
  • PCR (38)
  • Centrifuge Tubes (27)
  • Deep Well Plates (23)
  • Magnetic Rod Sleeves (1)
  • Safety Goggles (1)
  • Robotic Tips (0)
Latest News
  • Different Types of Laboratory Tubes and Their Uses
  • Purpose and Precautions of Magnetic Rod Sleeve
  • Considerations for Precision Automated Pipetting
  • Why is Balancing Centrifuges Important?
Follow us
  • Twitter
  • Facebook
  • Youtube
  • Instagram
Resources
  • About Us
  • Contact Us
  • Products
  • Sitemap
  • Glossary
  • Tags
  • Privacy and Policy
  • Terms
© 2026 Chengdu Pulse Optics-tech Co., Ltd., All Rights Reserved.
Website Design & Support: jeawin.com
Links: Plastic Injection Molding, China Manufacturers.